magistrsko delo magistrskega študijskega programa II. stopnje Strojništvo
Marko Juričič (Author), Andrej Lebar (Mentor), Joško Valentinčič (Co-mentor)

Abstract

Rezanje z abrazivnim vodnim curkom (AVC) uporablja visokohitrostni vodni curek, kateremu dodajamo mineralni abraziv. Abrazivna zrna se v šobi močno pospešijo, zaradi svoje velike hitrosti in trdote skupaj z vodo ob stiku z obdelovancem odnašajo material. S tem postopkom lahko obdelujemo skoraj vse vrste materialov, ne glede na njihovo sestavo, strukturo in trdoto. Velika prednost tega postopka je ta, da ni toplotno vplivanega področja. Poznamo različne načine doziranja abraziva, najbolj pogosta sta dva načina: prvi je gravitacijski, kjer je masni pretok določen s premerom zaslonke, pri drugem masni pretok določamo tako, da spreminjamo hitrost vrtenja elektro motorja, ki poganja transportni trak ali kolo. V delu smo predstavili proces rezanja z AVC in pregledali literaturo o merjenju masnega pretoka zrnatih materialov. V eksperimentalnem delu smo izdelali dozirni sistem z vrtečim se kolesom, izmerili masne pretoke na treh različnih dozirnih sistemih in ovrednotili enakomernost masnega pretoka.

Keywords

magistrske naloge;abrazivni vodni curek;abrazivi;dozirni sistemi;masni pretoki;

Data

Language: Slovenian
Year of publishing:
Typology: 2.09 - Master's Thesis
Organization: UL FS - Faculty of Mechanical Engineering
Publisher: [M. Juričič]
UDC: 621.9:531/533(043.2)
COBISS: 16957979 Link will open in a new window
Views: 810
Downloads: 219
Average score: 0 (0 votes)
Metadata: JSON JSON-RDF JSON-LD TURTLE N-TRIPLES XML RDFA MICRODATA DC-XML DC-RDF RDF

Other data

Secondary language: English
Secondary title: Comparison of abrasive dosage systems for water jet cutting
Secondary abstract: Abrasive water jet cutting (AWJ) uses a high speed water jet to which a mineral abrasive is added. Abrasive grains are greatly accelerated in the nozzle, due to their high speed and hardness they remove material along with the water in contact with the workpiece. With this process, almost all types of materials can be machined, regardless of their composition, structure and hardness. The great advantage of this process is that there is no heat affected zone. There are different ways of dosing the abrasive, the most common are two methods: the first is gravity method, where the mass flow is determined by the diameter of the orifice, for the second, the mass flow is determined by varying the speed of electric motor that drives the conveyor belt or wheel. In this paper we presented the process of AWJ cutting and reviewed the literature on measuring mass flow of granular materials. In the experimental part we designed a dosage system with a rotating wheel, measured mass flow rates on three different dosing systems and evaluated the steadiness of mass flow rate.
Secondary keywords: abrasive water jet;abrasives;dosage systems;mass flow;
Type (COBISS): Master's thesis/paper
Study programme: 0
Embargo end date (OpenAIRE): 1970-01-01
Thesis comment: Univ. Ljubljana, Fak. za strojništvo
Pages: XXI, 64 str.
ID: 11270623
Recommended works:
, magistrsko delo magistrskega študijskega programa II. stopnje Strojništvo
, magistrsko delo magistrskega študijskega programa II. stopnje Strojništvo
, zaključna naloga Razvojno raziskovalnega programa I. stopnje Strojništvo
, magistrsko delo magistrskega študijskega programa II. stopnje Strojništvo
, magistrsko delo magistrskega študijskega programa II. stopnje Strojništvo