diplomsko delo - univerzitetni študij - 1. stopnja
Jaka Rupnik (Author), Anton Poje (Mentor)

Abstract

V diplomski nalogi smo raziskovali vpliv nabrušenosti verige motorne žage na jakost tresenja in učinkovitost prežagovanja, z namenom, da poudarimo izkušnje gozdnega delavca na pripravo verige motorne žage. Posebej nas je zanimalo, kako se uporaba ročno brušenih verig razlikuje po učinkovitosti in jakosti tresenja, od uporabe tovarniško nabrušene verigo. Prežagovanje smo izvedli z motorno žago Stihl 462 C-M, ter verigo Rapid Super (RS) s korakom 3/8. Deset verig, ki smo jih skrhali v vedru kremenčkovega peska, je nabrusilo pet delavcev z delovnim stažem, krajšim od enega leta in pet delavcev z delovnim stažem, daljšim od deset let. Ena veriga je ostala v tovarniškem stanju. Z uporabo vsake verige smo izvedli šest prežagovanj prizmiranega sortimenta smreke. Rezultati so pokazali, da je bila jakost tresenja za 2,6-krat večja na vodilnem ročaju, kot na nosilnem ročaju motorne žage. Najmanjša jakost tresenja je bila na vodilnem ročaju izmerjena pri uporabi tovarniške verige, na nosilnem pa pri uporabi verige, ki so jo nabrusili delavci začetniki. Največja učinkovitost prežagovanja je bila dosežena pri uporabi tovarniško nabrušene verige, ki je bila tako za 53% večja, kot pri uporabi verig, ki so jo nabrusili delavci s krajšim delovnim stažem. Rezultati raziskave potrjujejo vpliv izkušenosti na učinkovitost in jakost tresenja pri delu z motorno žago, sočasno pa izpostavljajo tudi pomembnost pravilne priprave, za učinkovito in varno delo v gozdni proizvodnji.

Keywords

tresenje rok in dlani;učinkovitost;brušenje verig;izkušenost delavcev;

Data

Language: Slovenian
Year of publishing:
Typology: 2.11 - Undergraduate Thesis
Organization: UL BF - Biotechnical Faculty
Publisher: [J. Rupnik]
UDC: 630*30+630*36(043.2)=163.6
COBISS: 208318211 Link will open in a new window
Views: 27
Downloads: 94
Average score: 0 (0 votes)
Metadata: JSON JSON-RDF JSON-LD TURTLE N-TRIPLES XML RDFA MICRODATA DC-XML DC-RDF RDF

Other data

Secondary language: English
Secondary title: ǂThe ǂimpact of experience at sharpening the chainsaw chain on the crosscutting performance and vibration levels
Secondary abstract: In this thesis, we explored the impact of a forestry worker's experience on the sharpening of chainsaw chains, focusing on HA vibration levels and cross-cutting efficiency, with the aim of highlighting the importance of worker experience in preparing chainsaw chains. We were particularly interested in how the use of hand-sharpened chains compares in terms of efficiency and vibration intensity to factory-sharpened chains. For the study, we used a Stihl 462 C-M chainsaw, and a Rapid Super (RS) chain with a pitch of 3/8 inch. Ten chains were dulled in a bucket of quartz sand and sharpened by five workers with less than one year of experience and five workers with over ten years of experience. One chain remained in factory condition. We used 11 different chains in total, performing six cross-cuts with each one on squared spruce timber. The results showed that vibration intensity was 2.6 times greater on the front handle compared to the rear handle for all chains tested. The lowest vibration level on the front handle was recorded with the factory-sharpened chain, while the lowest on the rear handle was with chains sharpened by less experienced workers. The highest cutting the chains sharpened by less experienced workers. The study confirms the impact of experience on cutting efficiency and vibration levels when working with a chainsaw, while also emphasizing the importance of proper chain preparation for efficient and safe work in forestry.
Secondary keywords: HA vibration levels;efficiency;chain sharpening;worker experience;
Type (COBISS): Bachelor thesis/paper
Study programme: 0
Thesis comment: Univ. v Ljubljani, Biotehniška fakulteta, Oddelek za gozdarstvo in obnovljive gozdne vire
Pages: 1 spletni vir (1 datoteka PDF (IX, 30 str.))
ID: 25105276