Sesanje polimernih filamentov

diplomsko delo Visokošolskega strokovnega študijskega programa I. stopnje Strojništvo

Primož Trobiš (Avtor), Jurij Prezelj (Mentor)

Povzetek

Diplomsko delo temelji na osnovi sesalne pištole, ki jo uporabljajo v podjetju AquafilSLO, ki se ukvarjajo s proizvodnjo poliamidnih filamentov in granulatov. Sesalna pištola služi kot pripomoček za navijanje filamenta s pomočjo stisnjenega zraka, ki ga proizvedemo v kompresorski postaji. Zaradi visokih stroškov priprave stisnjenega zraka smo naredili prototipni sesalnik, ki bi z manjšo močjo ter nižjimi stroški obratovanja opravljal enako nalogo. Prototipni sesalnik mora zagotavljati hitrost 100 m/s na vstopu v sesalno pištolo. Nadzvočno hitrost moramo zagotavljati s podtlakom. Izdelali smo prototipni sesalnik ter prototipne De Lavalove šobe, s katerimi smo se hoteli približati trenutnemu delovanju. Za ocenjevanje rezultatov smo izdelali merilno napravo, s katero smo izmerili sile ob sesanju filamenta. Tako smo primerjali rezultate obstoječega sistema z rezultati prototipnega sesalnika. Rezultati so pokazali, da trenutni prototipni sesalnik zagotavlja petkrat manjšo silo, kar pomeni, da se z rešitvijo nismo približali trenutnemu delovanju obstoječega sistema z uporabo stisnjenega zraka.

Ključne besede

diplomske naloge;sesalne pištole;De Lavalove šobe;filamenti;polimeri;stisnjen zrak;

Podatki

Jezik:	Slovenski jezik
Leto izida:	2019
Tipologija:	2.11 - Diplomsko delo
Organizacija:	UL FS - Fakulteta za strojništvo
Založnik:	[P. Trobiš]
UDK:	621.51:62-225:678(043.2)
COBISS:	16910107
Št. ogledov:	762
Št. prenosov:	171
Ocena:	0 (0 glasov)
Metapodatki:

Ostali podatki

Sekundarni jezik:	Angleški jezik
Sekundarni naslov:	Suction of polymer filaments
Sekundarni povzetek:	The thesis is based on the suction unit used in AquafilSLO Production of polyamide filaments and granules. It serves as a tool for filament winding. The suction unit is currently powerede by the compressed air produced in the compressor station. Due to the high cost of preparing the compressed air, we made a prototype of a suction unit that would perform the same task with lower power and consequently lower operating costs. It must provide a air sucction velocity of 100 m/s at the inlet of the suction unit. The aim is to achieve near supersonic velocity by vacuum. We have designed a prototype suction unit and prototype of De Laval nozzles to bring us closer to it's current performance. To evaluate the results, a measuring device was designed to measure the forces at which the filament was sucked. Thus, we compared the results of the existing system with the results of the prototype suction system. The results showed that the current prototype vacuum system provides five times less force, which means that the solution did not approximate the current operation of the existing system using compressed air. Further development is needed.
Sekundarne ključne besede:	thesis;suction units;De Laval nozzles;filaments;polymers;compressed air;
Vrsta dela (COBISS):	Diplomsko delo/naloga
Študijski program:	0
Konec prepovedi (OpenAIRE):	1970-01-01
Komentar na gradivo:	Univ. v Ljubljani, Fak. za strojništvo
Strani:	XXII, 41 str.
ID:	11218616