Mihael Brunčko (Avtor), Ivan Anžel (Avtor), Alojz Križman (Avtor)

Povzetek

Formiranje mikrostrukture med strjevanjem, ki je odvisno predvsem od hitrosti strjevalne fronte vSF in temperaturnega gradienta GSF v njeni bližini, močno vpliva na mehanske in druge lastnosti lite zlitine. Zato je za doseganje želenih lastnosti strjenih zlitin potrebno poznanje odvisnosti med vplivnimi parametri strjevanja ter nastajajočo mikrostrukturo. Merilne metode, ki omogočajo sprotno in neporušno spremljanje teh parametrov že v fazi formiranja mikrostrukture, so velik izziv pri razvoju modernih inženirskih materialov. V prispevku obravnavamo možnosti uporabe sprotnega merjenja spremembe električne upornosti med usmerjenim strjevanjem za določitev položaja in hitrosti strjevalne fronte vSF. Spremembo električne upornosti smo merili med usmerjenim strjevanjem vzorca evtektične zlitine Pb-Sn pri različnih hitrostih pomika vzorca iz grelne cone ter konstantnem temperaturnem gradientu peči. Tako dobljene vrednosti hitrosti strjevalne fronte vSF smo primerjali s tistimi, ki smo jih določili pri enakih pogojih strjevanja z meritvijo spremembe temperature s termočleni, nameščenimi v notranjosti vzorca.

Ključne besede

usmerjeno strjevanje;meritve električne upornosti;evtektična zlitina Pb-Sn;

Podatki

Jezik: Slovenski jezik
Leto izida:
Tipologija: 1.01 - Izvirni znanstveni članek
Organizacija: UM FS - Fakulteta za strojništvo
Založnik: Inštitut za kovinske materiale in tehnologije Ljubljana
UDK: 669.45:669.6:537.311
COBISS: 268202 Povezava se bo odprla v novem oknu
ISSN: 1580-2949
Št. ogledov: 1048
Št. prenosov: 83
Ocena: 0 (0 glasov)
Metapodatki: JSON JSON-RDF JSON-LD TURTLE N-TRIPLES XML RDFA MICRODATA DC-XML DC-RDF RDF

Ostali podatki

Sekundarni jezik: Angleški jezik
Sekundarni naslov: Monitoring of the eutectic Pb-Sn alloy during directional solidification
Sekundarni povzetek: Microstructure evolution during solidification primarily depends on the velocity vSF and the temperature gradient GSF of the solidification front. It has a great influence on the mechanical and other properties of the cast alloys. It is therefore important to know the relationship between the influential solidification parameters and the evolving microstructure if the desired properties of solidified alloys are to be achieved. Thus, the measurement methods that allow online and nondestructive monitoring of these parameters represent a great challenge in the evolution of modern engineering materials. In this paper we discuss the usability of in-situ measurements of electrical resistance changes during the directional solidification for tracing the position and the velocity of the solidification front vSF. The electrical resistance changes were measured during directional solidification on a sample of the Pb-Sn eutectic alloy at different pulling velocities for displacing samples from the heating zone and at a constant temperature gradient of the furnace. The obtained values of the solidification front velocities vSF were subsequently compared with the values determined during the same solidification conditions by measuring the temperature changes with thermocouples, placed inside the sample.
Sekundarne ključne besede: directional solidification;electrical resistance measurements;eutectic Pb-Sn alloy;
URN: URN:NBN:SI
Vrsta dela (COBISS): Znanstveno delo
Strani: str. 367-374
Letnik: ǂLetn. ǂ36
Zvezek: ǂšt. ǂ6
Čas izdaje: 2002
ID: 1746637