Lara Župec (Avtor), Peter Bohinc (Avtor), Mihael Brunčko (Avtor)

Povzetek

Čeprav je sodobni trend v fiksni protetiki v uporabi polnokeramičnih zobnih nadomestkov, so raziskave pokazale, da se še vedno najpogosteje uporabljajo kovinsko-porcelanski zobni nadomestki. Namen v tem prispevku predstavljene raziskave je ugotoviti, kako različne tehnike mehanske obdelave površine kovinskega ogrodja vplivajo na pojav napak v porcelanskem sloju ter mejni površini kovina-porcelan. V okviru izvedenih raziskav smo izdelali vzorce iz Co-Cr zlitine z različnimi metodami in tehnikami površinske obdelave. Sledila je priprava metalografskih obrusov s pomočjo katerih smo analizirali vpliv površinskih obdelav na spremembo makro- in mikrostrukture kovinskega ogrodja, porcelanskega plašča in mejne površine med njima. Rezultati opravljenih raziskav so pokazali, da je pojav napak pri vzorcih katerih kovinsko ogrodje je bilo obdelano z brusnim sredstvom v eni smeri minimalen, površina kovinskega ogrodja enakomerno hrapava z enakomerno povprečno debelino oksidne plasti 3,5µm. Pri vzorcih s kovinskim ogrodjem obdelanim z brusnim sredstvom v več smereh, smo opazili bolj hrapavo površino kovinskega ogrodja s prisotnostjo plastične deformacije površine kovinskega ogrodja, ki tvori tanjšo oksidno plast.

Ključne besede

kovinsko-porcelanska prevleka;mehanska obdelava kovinskega ogrodja;brusna sredstva;peskanje;mikrostruktira;

Podatki

Jezik: Slovenski jezik
Leto izida:
Tipologija: 1.01 - Izvirni znanstveni članek
Organizacija: UM FS - Fakulteta za strojništvo
UDK: 616.31
COBISS: 173363715 Povezava se bo odprla v novem oknu
ISSN: 2232-416X
Št. ogledov: 23
Št. prenosov: 1
Ocena: 0 (0 glasov)
Metapodatki: JSON JSON-RDF JSON-LD TURTLE N-TRIPLES XML RDFA MICRODATA DC-XML DC-RDF RDF

Ostali podatki

Sekundarni jezik: Angleški jezik
Sekundarni naslov: Influence of metal surface finishing on porcelain microstructure failures in porcelain-fused-to-metal dental restoration
Sekundarni povzetek: Although the current trend in fixed prosthetics is the use of full-ceramic dental restorations, research has shown that most commonly used are still metal-ceramic dental restorations. The purpose of the research presented in this paper is to find out how different techniques of mechanical treatment of the surface of the metal frame affect the occurrence of defects in the porcelain layer and the metal-porcelain interface. As part of the research, we produced samples from Co-Cr alloy using various surface treatment methods and techniques, followed by the preparation of metallographic tablecloths, with the help of which we analyzed the influence of surface treatments on the change in the macro- and microstructure of the metal framework, the porcelain veneer and the interface between them. The results of the conducted research showed that the occurence of defects in samples whose metal surface was treated with an abrasive in one direction is minimal, the surface of the metal framework is uniformly rough with an average thickness of the oxide layer of 3,5µm. In samples with a metal framework treated with an abrasive in several directions, we observed a rougher surface of the metal framework with the presence of plastic deformation of the surface of the metal framework, which forms a thinner oxide layer.
Sekundarne ključne besede: metal-ceramic crown;metal framework processing;abrasive stones;sandblasting;microstructure;
Vrsta dela (COBISS): Članek v reviji
Strani: str. 35-57
Letnik: ǂLetn. ǂ13
Zvezek: ǂšt. ǂ2
Čas izdaje: 2023
DOI: 10.18690/analipazu.13.2.35-58.2023
ID: 21193315