magistrsko delo
Gregor Ačko (Avtor), Zoran Ren (Mentor), Miran Ulbin (Komentor)

Povzetek

Skozi celotno zgodovino človeštva, je na razvoj civilizacij vplivalo odkritje novih materialov. Z znanjem o metalurgiji, ki ga danes poseduje človeška družba, vemo da je razvoj novih materialov odločilno vplival k razvoju naprednega kmetovanja, transporta, rokodelstva itd. Današnja industrija se usmerja predvsem materialom, ki so lahki in imajo dobro odpornost na obremenitve. Med nje spadajo avksetični materiali, ki so manj znani, vendar imajo unikatne mehanske lastnosti, ki se jih da uporabiti v različnih vejah industrije. Magistrsko delo obravnava »re -entrant« strukturo avksetičnih materialov, pri različnih kotih celic, ki sestavljajo slednjo strukturo. S pomočjo numeričnih analiz smo določili mehanske lastnosti teh struktur, ter jih primerjali z analitičnim modelom. Strukture smo pri numeričnih analizah, obremenili s pomiki, ki ponazarjajo tlačno obremenitev. Uporabili smo majhne pomike, saj uporabljen analitičen model ni uporaben pri večjih deformacijah. Pridobljeni rezultati so predstavljeni na grafih, kjer je jasno vidna razlika med posameznimi koti struktur. Na podlagi pridobljenih rezultatov, lahko vidimo prednosti avksetičnih struktur v primerjavi s konvencionalnimi strukturami. S temi dejstvi ne trdimo da so konvencionalne strukture slabše od avksetičnih, vendar imajo slednje v posameznih pogojih, določene prednosti.

Ključne besede

avksetične strukture;strukturne lastnosti;negativno Poissonovo število;višja strukturna gostota;napake v numeričnem modelu;CATIA V5;Abaqus;magistrske naloge;

Podatki

Jezik: Slovenski jezik
Leto izida:
Tipologija: 2.09 - Magistrsko delo
Organizacija: UM FS - Fakulteta za strojništvo
Založnik: [G. Ačko]
UDK: 004.942:620.18(043.2)
COBISS: 19782166 Povezava se bo odprla v novem oknu
Št. ogledov: 1156
Št. prenosov: 142
Ocena: 0 (0 glasov)
Metapodatki: JSON JSON-RDF JSON-LD TURTLE N-TRIPLES XML RDFA MICRODATA DC-XML DC-RDF RDF

Ostali podatki

Sekundarni jezik: Angleški jezik
Sekundarni naslov: Modelling and simulation of selected auxetic materials
Sekundarni povzetek: Throughout human history, development of civilizations was affected by the discovering of new materials. With the knowledge of metallurgy, which today is possess by human society, we know that the development of new materials have a decisive influence to development of modern farming, transport, handcraft, etc. Nowadays industry is focused on materials that are lightweight and have good stress resistance. This includes the auxetic materials which are less well – known, but they have unique mechanical properties, which can be used in various branches of industry. Master's thesis discuss about materials with »re - entrant« auxetic structure, with different angles of the cells which are building blocks of structure. By using of numerical analyzes were determined mechanical properties of those structures, and compared them with analytical model. We have encumber structures, with small shifts representing compressive loading. We have used a small displacements, because analytical model is not useful for large deformations. Obtained results are presented in charts, where it's clearly visible difference between the angles of structures. Based on obtained results, we can see advanteges of auxetic structures compared wit conventional structures. With these facts, we do not claim that conventional structures are worse, but auxetic structures have few advantages in some conditions compared with convention
Sekundarne ključne besede: auxetic structures;structure properties;negative Poisson ratio;higher structural density;errors in numerical model;CATIA V5;Abaqus;
URN: URN:SI:UM:
Vrsta dela (COBISS): Magistrsko delo/naloga
Komentar na gradivo: Univ. v Mariboru, Fak. za strojništvo
Strani: VIII, 36 f.
ID: 9148363