Št. zadetkov: 10
Izvirni znanstveni članek
Oznake:
In order to get small-dimensioned shape memory alloys (SMAs) with good functional and mechanical properties, a rapid solidification technique was employed. This paper discusses the use of different melt-spinning procedures for the preparation of proper thin NiTi ribbons. Metallographic characterizat ...
Leto:
2012
Vir:
Fakulteta za strojništvo (UM FS)
Izvirni znanstveni članek
Oznake:
Microstructural changes during vacuum carburizing of steels
Leto:
2011
Vir:
Fakulteta za strojništvo (UM FS)
Objavljeni znanstveni prispevek na konferenci
Oznake:
metalurgija;kovinski materiali;lastnosti;mikrostruktura;notranja oksidacija;metallurgy;metallic materials;properties;microstructure;internal oxidation;
The creation of desired microstructures by internal oxidation
Leto:
2005
Vir:
Fakulteta za strojništvo (UM FS)
Izvirni znanstveni članek
Oznake:
metalurgija;zlitina Ag-Sn;notranja oksidacija;električna upornost;metallurgy;Ag-Sn alloy;internal oxidation;electrical resistance;
This paper presents a non-destructive measurement method that enables identification and characterization of phenomena during internal oxidation of metallic materials as well as monitoring the kinetics of internal oxidation using "in-situ" electrical resistance measurements. A special laboratory dev ...
Leto:
2007
Vir:
Fakulteta za strojništvo (UM FS)
Objavljeni znanstveni prispevek na konferenci
Oznake:
metalurgija;zlitine z oblikovnim spominom;lastnosti;mikrostruktura;metallurgy;shape memory alloys;properties;microstructure;
This work addresses three topics: the generation of two-way shape memory effects in NiTi, NiTiW and CuAlNi wire materials and the investigation of the long term stability of these effects; investigations on thin CuAlNi films produced by PVD; investigation on thin CuAlNi ribbons produced by melt-spin ...
Leto:
2005
Vir:
Fakulteta za strojništvo (UM FS)
Izvirni znanstveni članek
Oznake:
focussed ion beam;FIB;metallography;melt-spinning;shape memory alloy;Cu-Al-Ni;
This work investigates the possibilities for applying a focussed ion beam (FIB) for the metallographic preparation and characterization of Cu-Al-Ni melt-spun ribbons. Two alloys were selected for this reason: CuAl13Ni4 and CuAl15Ni4. The microstructure of the first alloy was fully martensitic and th ...
Leto:
2007
Vir:
Fakulteta za strojništvo (UM FS)
Izvirni znanstveni članek
Oznake:
Practically all metals and alloys survive high-temperature exposure by growing oxide scales and/or by precipitation of the oxide particles in the matrix. Formed products can grow in shape of external oxide layers on surfaces, or as discrete oxide particles precipitated in a metal matrix. The first c ...
Leto:
2013
Vir:
Fakulteta za strojništvo (UM FS)
Izvirni znanstveni članek
Oznake:
metalurgija;zlitine z oblikovnim spominom;zlitina Cu-Al-Ni;mikrostruktura;metallurgy;shape memory alloys;Cu-Al-Ni alloy;microstructure;melt spinning;
Cu-Al-Ni shape memory alloys (SMAs) are currently the only available high temperature SMAs, showing a good resistance against functional fatigue. In polycrystalline state, they are very brittle and exhibit, in general, only small reversible deformations. By melt spinning, thin Cu-Al-Ni ribbons can b ...
Leto:
2005
Vir:
Fakulteta za strojništvo (UM FS)
Izvirni znanstveni članek
Oznake:
shape memory;two-way-effect;Ni-Ti alloy;stability;martensic transformation;fatigue;
This work presents a study of the degradation of the Two-Way Shape Memory Effect (TWSME) due to working cycles. An intrinsic TWSME was induced in wire specimens of a near equiatomic Ni-Ti alloy by thermomechanical training. The development of the two way strain was analysed and discussed with respec ...
Leto:
1997
Vir:
dLib.si Digitalna knjižnica Slovenije
Izvirni znanstveni članek
Oznake:
polyoxymethylene;cellulose fibers;processing;characterization;tribology;
Natural fibers are promising bio-based materials to use as reinforcements in polymer composites as often more affordable and accessible alternatives to fossil-based fibers, especially because of their superior sustainability. Polyoxymethylene (POM) is a widely used engineering thermoplastic, which h ...
Leto:
2023
Vir:
Fakulteta za strojništvo (UL FS)