Iskalni niz:
išči po
išči po
išči po
išči po
Vrsta gradiva:
Jezik:
Št. zadetkov: 5
Mathematical model for the selection of processing parameters in selective laser sintering of polymer products
Ana Pilipović, Igor Drstvenšek, Mladen Šercer
Izvirni znanstveni članek
Oznake: proizvodni sistemi;inteligentne metode;3D skeniranje;manufacturing system;inteligent methods;3D scanning;
Additive manufacturing (AM) is increasingly applied in the development projects from the initial idea to the finished product. The reasons are multiple, but what should be emphasised is the possibility of relatively rapid manufacturing of the products of complicated geometry based on the computer 3D ...
Leto: 2014 Vir: Fakulteta za strojništvo (UM FS)
Hydrophobicity and retention coefficient of selected bile acid oxo derivatives
Mihalj Poša, Ana Pilipović, Mladena Lalić, Jovan Popović
Izvirni znanstveni članek
Oznake: organska kemija;holna kislina;hidrofobnost;tekočinska kromatografija;retencijski koeficient;
Leto: 2010 Vir: dLib.si Digitalna knjižnica Slovenije
Development of a 3D printer for thermoplastic modelling
Bogdan Valentan, Dušan Pogačar, Tomaž Brajlih, Tjaša Zupančič Hartner, Ana Pilipović, Igor Drstvenšek
Izvirni znanstveni članek
Oznake: polymers;rapid prototyping;additive technologies;3D print;
Dodajalne tehnologije vstopajo na trg v vseh cenovnih segmentih, razvoj novih naprav in materialov pa je v konstantnem teku. Naprave s ceno pod 2000 EUR so vse bolj zanimive za uporabo doma in v izobraževalne namene. Članek prikazuje razvoj 3D-tiskalnika, ki izdela izdelek s ciljnim nalaganjem mater ...
Leto: 2012 Vir: Fakulteta za strojništvo (UM FS)
ǂA ǂfast method to predict the cooling time of wax for investment casting procedure
Bogdan Valentan, Ana Pilipović, Tomaž Brajlih, Peter Sever, Ivo Pahole, Mirko Ficko, Jože Balič, Igor Drstvenšek
Izvirni znanstveni članek
Oznake: odlivki;vosek;silikonski gumijasti modeli;čas hlajenja;hitra proizvodnja;
The investment casting of metal parts is a rapid tooling/manufacturing method for small series production, where wax pattern is produced separately and then extracted from the mould. The wax parts commonly used as patterns are usually obtained after wax casting silicone rubber moulds. The time neede ...
Leto: 2012 Vir: Fakulteta za strojništvo (UM FS)
Genetic aspects linked to production and use of forest reproductive material (FRM)
Dušan Gömöry, Katri Himanen, Mari Mette Tollefsrud, Claes Uggla, Hojka Kraigher, Sandor Bordacs, Paraskevi Alizoti, Stuart A'Hara, Aline Frank, Gunnar Friis Proschowsky, Josef Frýdl, Thomas Geburek, Monique Guibert, Mladen Ivanković, Ana Jurše, Stuart Kennedy, Jan Kowalczyk, Heike Liesebach, Tiit Maaten, Andrej Pilipović, Roberta Proietti, Volker Schneck, Alain Servais, Brynjar Skúlason, Christoph Sperisen, Frank Wolter, Tefide Yüksel, Michele Bozzano
Znanstvena monografija
Oznake: gozdna genetika;gozdni genski material;forest reproductive material;
This report summarises the current state of knowledge in genetic aspects linked to the production and use of forest reproductive material (FRM). The first chapter describes the different categories of FRM, considers the strategic choice between artificial and natural regeneration in the face of clim ...
Leto: 2021 Vir: Repozitorij Univerze v Ljubljani (RUL)
Št. zadetkov: 5
Ključne besede:
Leto izdaje:
Avtorji:
Repozitorij:
Tipologija:
Jezik: