Št. zadetkov: 13
Izvirni znanstveni članek
Oznake:
tribology;polymer composites;polyoxymethylene;cellulose fibers;wear resistance;
Polyoxymethylene (POM), an engineering polymer commonly used in tribological applications, is often reinforced with fossil-based fibers such as carbon and/or glass fibers to improve its properties. To find more sustainable solutions, in this study, the tribological performance of POM/short cellulose ...
Leto:
2024
Vir:
Fakulteta za strojništvo (UL FS)
Izvirni znanstveni članek
Oznake:
polyoxymethylene;cellulose fibers;processing;characterization;tribology;
Natural fibers are promising bio-based materials to use as reinforcements in polymer composites as often more affordable and accessible alternatives to fossil-based fibers, especially because of their superior sustainability. Polyoxymethylene (POM) is a widely used engineering thermoplastic, which h ...
Leto:
2023
Vir:
Fakulteta za strojništvo (UL FS)
Izvirni znanstveni članek
Oznake:
shape memory;two-way-effect;Ni-Ti alloy;stability;martensic transformation;fatigue;
This work presents a study of the degradation of the Two-Way Shape Memory Effect (TWSME) due to working cycles. An intrinsic TWSME was induced in wire specimens of a near equiatomic Ni-Ti alloy by thermomechanical training. The development of the two way strain was analysed and discussed with respec ...
Leto:
1997
Vir:
dLib.si Digitalna knjižnica Slovenije
Izvirni znanstveni članek
Oznake:
In order to get small-dimensioned shape memory alloys (SMAs) with good functional and mechanical properties, a rapid solidification technique was employed. This paper discusses the use of different melt-spinning procedures for the preparation of proper thin NiTi ribbons. Metallographic characterizat ...
Leto:
2012
Vir:
Fakulteta za strojništvo (UM FS)
Izvirni znanstveni članek
Oznake:
Microstructural changes during vacuum carburizing of steels
Leto:
2011
Vir:
Fakulteta za strojništvo (UM FS)
Objavljeni znanstveni prispevek na konferenci
Oznake:
metalurgija;kovinski materiali;lastnosti;mikrostruktura;notranja oksidacija;metallurgy;metallic materials;properties;microstructure;internal oxidation;
The creation of desired microstructures by internal oxidation
Leto:
2005
Vir:
Fakulteta za strojništvo (UM FS)
Izvirni znanstveni članek
Oznake:
metalurgija;zlitina Ag-Sn;notranja oksidacija;električna upornost;metallurgy;Ag-Sn alloy;internal oxidation;electrical resistance;
This paper presents a non-destructive measurement method that enables identification and characterization of phenomena during internal oxidation of metallic materials as well as monitoring the kinetics of internal oxidation using "in-situ" electrical resistance measurements. A special laboratory dev ...
Leto:
2007
Vir:
Fakulteta za strojništvo (UM FS)
Izvirni znanstveni članek
Oznake:
plemenita zlitina z visoko entropijo;strjevanje;mikrostruktura;metastabilnost;high entropy noble alloy;solidification;microstructure;metastability;
High entropy alloys (HEA) represent a relatively new class of materials with promising properties for various applications. In recent years, these alloys have received considerable attention as potential heterogeneous catalysts in chemical and electrochemical reactions. Their enhanced catalytic acti ...
Leto:
2024
Vir:
Fakulteta za strojništvo (UM FS)
Objavljeni znanstveni prispevek na konferenci
Oznake:
metalurgija;zlitine z oblikovnim spominom;lastnosti;mikrostruktura;metallurgy;shape memory alloys;properties;microstructure;
This work addresses three topics: the generation of two-way shape memory effects in NiTi, NiTiW and CuAlNi wire materials and the investigation of the long term stability of these effects; investigations on thin CuAlNi films produced by PVD; investigation on thin CuAlNi ribbons produced by melt-spin ...
Leto:
2005
Vir:
Fakulteta za strojništvo (UM FS)
Izvirni znanstveni članek
Oznake:
plastomagneti;tehnologija ciljnega nalaganja;mikrostruktura;poliranje z ionskim žarkom;preiskava materialov;bonded magnets;fused deposition modelling;microstructure;Ion beam polishing;
Bonded magnets are composite materials consisting of polymer matrix and magnetic powders, prepared by rapid solidification processes from Nd-Fe-B alloys. They are synthesised by the compounding process on a twin-screw extruder, whereby, the finished products of complex shapes can be made from bonded ...
Leto:
2024
Vir:
Fakulteta za strojništvo (UM FS)